Features
A total of 10 buses
4 group, 4 auxiliary and the main stereo.
Insert point on all channel inputs
Group outputs (1-4), and the main stereo outputs.
4 auxiliary sends
2 pre, 2 post fader; user programmable.
Input and output signals
Can be monitored via the stereo cue bus.
2 fully assignable (line level) tape inputs
This is for connecting tape-, CD-players, etc.
Electronically-balanced
It also has low impedance XLR type microphone inputs.
Balanced phone jack line inputs.
Clear screen print legend and rotary control scaling
This is for optimum S/N operation.
Dedicated tape recorder outputs
Pre-stereo master fader.
20dB attenuation pad switch
Input channel peak indicator
Illuminates 3dB before clipping.
+48 phantom powering
The phantom powering is for the condenser type microphones.
Low noise, high rejection integral power supply.
Assignable VU meters
The meters come with integral peak LED.
Input Cue Led
The Input Cue Led indicates when an input cue switch is active.
L and R Cue Signal Leds
They indicate the presence of a signal in an input channel.
Four-band EQ
Four-band parametric EQ consists of fixed frequency shelving high and low EQs, and two variable frequency peak type mid-band EQs. All EQ's provide up to 15dB of boost or cut, and the high EQ is centered at 10kHz and the low, at 100Hz. The low mid EQ's center frequency can be set from 80 Hz to 1.6 kHz and the high mid EQ, from 400 Hz to 8kHz. The choice of center frequencies and the overlap between frequency bands allows you to perform detailed equalization across the audio spectrum.
Auxiliaries
Four auxiliary sends are provided: auxiliaries 1 and 2 are configured pre-fader, pre-EQ, pre-HPF, and auxiliaries 3 and 4 are post fader.
Monitor, route and mute
Input channels can be routed to any pair of group buses (1 and 2, or 3 and 4) or to the stereo bus. Monitoring is possible using the channel CUE switch, which, when selected, feeds the channel signal onto the cue bus, then to the headphone output. The cue switch is unaffected by the channel on/off switch, allowing you to monitor a channel even when it is muted.
Technology
Audio & Video
Specs
Specifications
| Frequency Response | 20 Hz - 20kHz +1, -3dB @ +4dB into 600 ohm | |
|---|---|---|
| THD | <0.1% 20 Hz- 20kHz @ +14dB into 600 ohm | |
| Equivalent Input Noise | -128 dB | |
| Residual Noise | -97dB | |
| Output Noise /Group Out | -80 dB Master faders- nominal, no input channel routing switches on. -64dB Master faders-- nominal, 1 channel fader-nominal. | |
| Output Noise/ Stereo Out | -79dB Master Faders- nominal, no input channel routing switches on. -64dB Master faders- nominal, 1 channel fader- nominal. | |
| Output Noise/ Aux Out | -77dB Aux out control- nominal, all input channel AUX controls- off. -64dB AUX out control- nominal, 1 input channel AUX control- nominal. | |
| Output Noise/ Matrix out | -95dB Matrix out controls- nominal, all matrix mix controls- off. | |
| Max Voltage Gain/ Ch In to Group Out | 84dB | |
| Max Voltage Gain/ Ch In to Stereo Out | 84dB | |
| Max Voltage Gain/ Ch In to Grp to Stereo Out | 94 dB | |
| Max Voltage Gain/ Ch In to Aux Out | 76 dB (pre fader) | |
| Max Voltage Gain/ Ch In to Ch Insert | 60dB | |
| Max Voltage Gain/ Tape In to Group Out | 30dB | |
| Max Voltage Gain/ Return to Group Out | 16 dB | |
| Max Voltage Gain/ Talkback In to Group Out | 70 dB | |
| Max Voltage Gain/Sub In to Grp to Stereo Out | 10dB | |
| Max Voltage Gain/ Sub In to Aux | 6dB | |
| Input Gain Control Range | 44 dB variable | |
| Pad Switch | 0/20dB | |
| EQ Characteristics/ High EQ | +/-15 dB @ 10kHz shelving | |
| EQ Chara. High-Mid EQ | +/-15dB @ 400- 8 kHz peaking | |
| EQ Chara./ Low-Mid EQ | +/-15dB @ 80 - 1.6kHz peaking | |
| EQ Chara./ Low EQ | +/-15dB @ 100 Hz shelving | |
| High Pass Filter | 80 Hz roll off, 12dB/ octave | |
| Crosstalk/ Adjacent input channels | -70dB @ 1kHz | |
| Crosstalk/ Input to output | -70dB @ 1kHz | |
| CH Peak Indicator | Illuminates 3dB below clipping (post EQ) | |
| Cue Signal Indicator | Illuminates when a signal 20dB below the nominal level is present on the cue bus. | |
| VU Meters | OVU= +4 dB Peak LED illuminates 3dB below clipping. | |
| Phantom Power Supply | +48V DC | |
| Dimensions (W x H x D) | 923 x 185 x 739 mm (36-5/16" x 7-5/16" x 29-1/8") | |
| Weight | 29 kg (63 lbs15 oz) | |
| Power Requirements and Consumption | 120V, 60 Hz, 80 W ( US and Canadian models) 240V, 50Hz, 80W (British model) 230V, 50Hz, 80W (General model) | |
