﻿N1X
Owner's Manual


Assembling the Unit
When assembling the unit, consult a qualified AvantGrand dealer.

CAUTION
Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble the unit in the appropriate sequence.
Since this product is very heavy, make sure that a sufficient number of people are on hand to help, so you can assemble it safely and easily.
Be sure to use only the included screws. Do not use any other screws. Inappropriate screws may cause damage or malfunction of the product. Be sure to insert screws of the proper size in the correct hole locations.
Be sure to tighten all screws upon completing assembly of each unit.
To disassemble, reverse the assembly sequence.

Have a Phillips-head (plus) screwdriver of the appropriate size ready.

(Figure)

Remove all parts other than the main unit from the box. Confirm that all parts shown in the illustration are provided. Do not remove the main unit from the box prior to step 3.

(Figure)
Main Unit
Leg (L)
Leg (R)
Speaker box
Be sure to lay the packaging sheet or other protective sheet on the floor and under the instrument.
6 x 30 mm long screws x 10
6 x 20 mm short screws x 6
AC power cord x 1
Headphone hanger
4 x 10 mm thin screws x 2

1	Attach the legs to the speaker box.
1-1	Attach the leg (L) to the side of the speaker box using three short screws (6 x 20 mm).
1-2	While pressing the bracket on the leg against the speaker box, securely tighten the screws that were attached.
1-3	Follow the same steps to attach the leg (R).

(Figure)

1-4	Raise the speaker box.

(Figure)
Do not hold here.

2	Detach the speaker net.

(Figure)

2-1	Remove the two screws. These screws are used in step 6.
2-2	Detach the speaker net.

3	Mount the main unit.
3-1	Mount the main unit on the speaker box while aligning the rear of the main unit with the rear of the speaker box, and each lateral side of the main unit with the lateral side of the legs.

CAUTION
Be careful not to pinch your fingers when mounting the main unit.

(Figure)
Hold here.

3-2	Move the main unit slightly toward the rear side, then adjust its position so that the projecting pin on the metal brackets on the bottom of the main unit will lock into the notch on the metal brackets of the legs (L/R).

(Figure)

4	Secure the main unit.
Secure the main unit using ten long screws (6 x 30 mm).

(Figure)

5	Connect the speaker cord and pedal cord.

(Figure)

5-1	Remove the vinyl tie attaching the speaker cord and pedal cord.
5-2	Insert the speaker cord plug into the connector so that the tab extends toward the front when viewed from the rear.
5-3	Insert the pedal cord plug into the pedal connector in the correct orientation.

Connecting the pedal cord
Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly.

(Figure)

5-4	Use vinyl ties to bundle the speaker cord and pedal cord.

6	Attach the speaker net.
6-1	Attach the speaker net.

(Figure)

6-2	Affix the speaker net with the screws unloosed at step 2.

(Figure)

7	Insert the AC power cord plug into the [AC IN] connector.

(Figure)
[AC IN] connector

8	Rotate the adjuster until it comes in firm contact with the floor surface.

(Figure)

9	Attach the headphone hanger.
Use the two thin screws (4 x 10 mm) to attach the hanger as shown in the illustration.

(Figure)

After completing the assembly, please check the following.
Are there any parts left over?
-> Review the assembly procedure and correct any errors.
Is the instrument clear of doors and other movable fixtures?
-> Move the instrument to an appropriate location.
Does the instrument make a rattling noise when you shake it?
-> Tighten all screws.
Is the power cord inserted securely into the sockets?
-> Check the connection.

CAUTION
If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws.


This is the end of the file.
