﻿CVP-701 Owner's Manual

Registration Memory – Saving and Recalling Custom Panel Setups –

(Figure)
The Registration Memory function allows you to save (or "register") virtually all panel settings to a Registration Memory button, and then instantly recall your custom panel settings by simply pressing a single button. The registered settings for eight Registration Memory buttons should be saved as a single Bank (file).

Registering Your Panel Setups
1	Set up the panel controls (such as Voice, Style, effects, and so on) as desired.
Refer to the separate Data List for a list of parameters that can be registered with the Registration Memory function.
2	Press the [MEMORY] button in the REGISTRATION MEMORY section.
The display for selecting the items to be registered appears.
(Figure)
3	Select the items you want to register.
Select the desired item by using the [1 Up Down] – [6 Up Down] buttons, then enter or remove the checkmark by using the [7 Up]/[8 Up] (MARK ON) / [7 Down]/[8 Down] (MARK OFF) buttons.
To cancel the operation, press the [I] (CANCEL) button.
4	Press one of the REGISTRATION MEMORY [1] – [8] buttons to which you wish to memorize the panel setup.
The memorized button becomes red, which indicates the number button contains data and its number is selected.
NOTICE
If you select the button whose lamp is lit in red or green here, the panel setup previously memorized to the button will be erased and replaced by the new settings.
(Figure)

About the lamp status
Red:	Data registered and currently selected
Green:	Data registered but not currently selected
Off:	No data registered

5	Register various panel setups to other buttons by repeating steps 1 – 4.
The registered panel setups can be recalled by simply pressing the desired number button.
NOTE
The panel setups registered in the numbered buttons are preserved even when you turn off the power. If you want to delete all the eight current panel setups, turn the power on while holding the B6 key (right-most B key on the keyboard).

Saving the Registration Memory as a Bank File
You can save all eight registered panel setups as a single Registration Memory Bank file.
(Figure)
Bank 01
Bank 02
Bank 03	
Bank 04
1	Press the REGIST BANK [+] and [-] buttons simultaneously to call up the Registration Bank Selection Display.
NOTE
In general, Registration Memory data (Bank files) is compatible among the models CVP-709/705/701. However, the data may not be perfectly compatible, depending on the specifications of each model.
(Figure)
2	Call up MENU2 at the right bottom of the display by pressing the [8 Down] button as necessary.
3	Press the [6 Down] (SAVE) button to save the Bank file.
For instructions on saving, refer to the operation steps (starting from Step 4) on page 81.

Recalling a Registered Panel Setup
The saved Registration Memory Bank files can be recalled by using the REGIST BANK [-]/[+] buttons or the following procedure.
NOTE
You can instantly call up the information display of the currently selected Registration Memory Bank by pressing the [DIRECT ACCESS] button and one of the REGISTRATION MEMORY [1] – [8] buttons in sequence.
NOTE
When recalling the setups including Song/Style/Audio file selection from a USB flash drive, make sure that the appropriate USB flash drive including the registered Song/Style is connected to the [USB TO DEVICE] terminal.
1	Press the REGIST BANK [+] and [-] buttons simultaneously to call up the REGISTRATION BANK Selection Display.
(Figure)
2	Press one of the [A] – [J] buttons to select a Bank.
You can also use the [DATA ENTRY] dial and the [ENTER] button to select a Bank.
3	Press one of the green-lit numbered buttons ([1] – [8]) in the Registration Memory section.

(Table)
Advanced Features
Refer to the Reference Manual on the website, Chapter 9.		
Deleting or renaming the Registration:	Bank Selection display | [A] – [J] | [8 Down] MENU1 | [7 Down] (EDIT) 
Confirming the Registration Memory information:	Bank Selection display | [A] – [J] | [8 Down] MENU1 | [6 Down] (INFO)
Disabling recall of specific items:	[FUNCTION] | TAB [Left][Right]  MENU1 | [C] REGIST SEQUENCE/FREEZE | TAB [Left][Right]  FREEZE
Calling up Registration Memory numbers in order:	[FUNCTION] | TAB [Left][Right]  MENU1 | [C] REGIST SEQUENCE/FREEZE | TAB[Left][Right]  REGISTRATION SEQUENCE
(Table End)

This is the end of the file.