RUio0804-D I/O Rack New

		RUio0804-D
General specifications
I/O Connectors	Analog Input	8
I/O Connectors	Analog Output	4
Sampling frequency rate	External	44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz ±200 ppm +4.1667%, +0.1%, −0.1%, −4.0% ±200 ppm
Signal delay		Less than 1.7 ms@Fs=96 kHz, 2.0 ms@Fs=48 kHz. RUio0804-D INPUT to RUio0804-D OUTPUT connect with DM5 using Dante. Dante Receive Latency set to 0.25 ms
Total harmonic distortion		Less than 0.05% +4 dBu@20 Hz - 20 kHz, GAIN : 0 dB into 10k Ω, Less than 0.15% +4 dBu@20 Hz - 20 kHz, GAIN: +64 dB into 10k Ω
Frequency response		+0.5, –1.5 dB 20 Hz - 20 kHz, refer to +4 dBu output @1 kHz, input to output, Fs= 48 kHz or 96 kHz
Dynamic range		114 dB typ., DA Converter, 109 dB typ., Input to Output, GAIN: 0 dB
Hum & noise level	Equivalent input noise	-128 dBu typ., GAIN: +64 dB
Hum & noise level	Residual output noise	-88 dBu, main stereo channel off
Crosstalk		INPUT: -100 dB, adjacent inputs, GAIN: 0 dB, @1 kHz, OUTPUT: -100 dB, input to output, @1 kHz
Power requirements		100–240 V, 50 Hz/60 Hz
Power consumption		30 W
Dimensions	W	480 mm (18.9”)
	H	44 mm (1.7”)
	D	369 mm (14.5”)
Net weight		3.7 kg (8.2lb)
Accessories		Read This First × 1, AC Power cord × 1
Others		NC Value: Fan Speed LOW: NC=20 / HIGH: NC=25 (Measurement position: 1 m from the front of the unit), Operating temperature range: 0 to 40°C, Storage temperature range: -20 to 60°C

Total harmonic distortion is measured using an 80 kHz, 48 dB/octave low pass filter.
Hum & noise levels are measured using an A-weight filter.
Crosstalk is measured using a 22 kHz, 48 dB/octave filter.

Analog Input Standards ^34

Input Terminal	GAIN	Actual Source Impedance	For Use with Nominal	Input Level			Connector
Input Terminal	GAIN	Actual Source Impedance	For Use with Nominal	Sensitivity ^*1	Nominal	Max.before clip	Connector
INPUT 1–8	+64 dB	10 kΩ	50–600 Ω Mics 600 Ω Lines	−80 dBu (0.078 mV)	−60 dBu (0.775 mV)	−40 dBu (7.75 mV)	XLR 3-hole chassis (Balanced) ^*2
INPUT 1–8	0 dB	10 kΩ	50–600 Ω Mics 600 Ω Lines	−16 dBu (123 mV)	+4 dBu (1.23 V)	+24 dBu (12.3 V)	XLR 3-hole chassis (Balanced) ^*2

*1 Sensitivity is the minimum level needed to output +4 dBu (1.23 V) or the specified level when the gain is set to maximum. (All faders and level controls are set to maximum.)
*2 1=GND, 2=HOT, 3=COLD
*3 0 dBu = 0.775 Vrms.
*4 +48V DC (phantom power) is supplied to INPUT XLR type connectors via each individual software-controlled switch.

Analog Output Standards ^*2

Input Terminal	Actual Source Impedance	For Use with Nominal	Output Level ^*3		Connector
Input Terminal	Actual Source Impedance	For Use with Nominal	Nominal	Max.before clip	Connector
OUTPUT 1–4	75 Ω	10 kΩ Lines	+4 dBu (1.23 V)	+24 dBu (12.3 V)	XLR 3-pin chassis (Balanced) ^*1